Thursday, 9 June 2016

Test shot of computer component

This page carries on from Coin test focus stacking Mk II.

Here is another test photograph that I have taken with my new focus stacking rig. It was stacked from 732 images, which were each taken at 1.6 second exposure, at x4 magnification, and 10 micro metres apart as the camera moved towards the subject. Only natural light was used. The images were stacked using Helicon Focus. 

The subject of the photograph is a small computer component that I cut out of my old flatbed scanner. 

This is the item photographed using a Canon Ixus camera. 

Here are some of the slices that were combined to make the image:

This is continued at 10x magnification with a teleconverter

Monday, 6 June 2016

Coin test Focus Stacking system MkII

This follows on from Focus Stacking System MkII

I have set the system up and run it with a 3x magnification test photo of a 5p coin.

The step size was 10 micro metres.
The delay between stepper motor steps was 0.0001 second.
The camera was set on manual mode, with a 1.6 second exposure on f/2.8.
Only natural light was used.

1242 slices (individual photos) were taken. This took about 2 hours. The process is entirely automated so I only had to start the script running and then leave it to get on with the job.

Below are some photos of the setup:

In my initial test, the teeth of the cogs kept disengaging under the opposing forces of the motor and the heavy camera. I wedged the board in place with some wood, and weighed the wood down with heavy books. 

This is the setup from the other side. The coin is on a paint pot and a blob of blu tac, which makes it very stable and allows easy height adjustment. The lens of the camera is propped up on a screwdriver. 

There is quite a long working distance between the camera and coin because I was only working at x3 magnification. 

Here are a few examples of individual shots taken by the camera:

I did not photograph right through to the back of the coin, because the camera ran out of batteries before I reached that point. 

Here is the stacked image from Helicon Focus:

So far so good...

This page carried on at Test shot of computer component.

Thursday, 2 June 2016

Focus Stacking setup MkII

Here is my latest attempt at building focus stacking equipment. This post follows on from "Fern Gametophyte Photograph"

This project is a collaboration between many people. The principles of the design came from the lovely folks at the forum. The design is particularly based on the Bratcam, designed by Chris Slaybaugh. The focus block was given to me as a gift by one of the forum members (Doc.Al). The electronics and programming were done by my husband, Tim Deegan. I did everything else.

Here is the setup. The focus block, on which the camera rests, is a block from a Nikon Optiphot or Labophot microscope. It was sawn out of the microscope by Doc.Al, and he also drilled holes in it, which have allowed me to fasten it to the board. The board is a piece of discarded kitchen worktop.

Below is a close-up shot of the camera mounted on the block. You can see the focus knob under the camera. It allows the top section of the block to be moved back and forth. There is a coarse and fine focus knob. On the other side of the focus block there are identical focus knobs. 

Switching now to the other side - below, you can also see the stepper motor, and the gearing that allows it to drive the fine focus control. The driver board (red) and the Raspberry Pi are also shown. These allow us to control the stepper motor. 

The stepper motor is an RS Pro Hybrid Stepper Motor 0.9°, 44 Ncm, 2.8 V, 1.68 A, 4-wire motor, which was bought from I intentionally brought quite a beefy motor in the hope that it would be less likely to burn out. It is also very square in the body, which helps to brace it against the board. 

Here is a close-up view of the gearing. The gear wheels were bought from and then the centres were drilled out or cut out with a hacksaw blade. The plastic gears were very soft, and easy to cut. 

Below in close-up is the driver board that allows the Raspberry pi to drive the stepper motor. The stepper motor is a 4-wire bipolar stepper motor, and requires and H-bridge chip to drive it. The board brought a number of specific advantages over just using an H-bridge and breadboard. The motor is able to turn a single complete turn of its spindle in 400 steps, but with the driver board this can be changed to 16 steps. The current reaching the motor can also be controlled so that the motor does not burn out. 

This is the Raspberry Pi, which sends the signals to run the motor. 

This is the arrangement of the wires (mostly for my notes, and in case they fall out and need to be put back in)

My husband, Tim, devised a system whereby the Raspberry Pi could also send a signal to fire the shutter of the camera automatically. He took apart a 3rd-party infra red Canon camera remote control and wired it up to the Raspberry Pi terminals. This means that he can write a single python programme to operate the stepper motor, and fire the shutter of the camera alternately. We have tried this and it works well. 

Below is a photograph of the infra red remote control with its new wiring. 

This is the other side. The wires are attached firmly to the board using the glue from a hot glue gun. 

Tim has carried out some experiments on the travel that is produced in the focus block using this stepper motor setup. He figured out that a single step of the stepper motor moves the top part of the focus block 1/128th of a μm (micro metre), which is very very good for our purposes.The movement is very smooth indeed. 

Thank you to everyone who helped to produce this amazing piece of machinery. :-) 
We are going to try taking some photos soon. Watch this space!